Force Transfer Around Openings

Advancements in Force Transfer Around Openings for Wood Framed Shear Walls

 

 

 

Advancements in Force Transfer Around Openings for Wood Framed Shear Walls is a recorded webinar given by Engineered Wood Specialist Karyn Beebe. It provides an overview of the force transfer around openings method of shear analysis as well as more detailed information on estimating forces around multiple openings with asymmetric piers and deflections for shear walls. Running time about 50 minutes. Note that this webinar is informational; no continuing education credits are available at this time.


Webinar: Resolving Wood Shear Wall Design Puzzles with Force Transfer Around Openings
DES415 — American Wood Council

Provides an overview of the force transfer around openings (FTAO) shear wall design approach, recent research in this area, and a side-by-side comparison of design results between segmented, perforated, and FTAO design methods. AIA, ICC, and NCSEA credits available. Presented by Jared Hensley, PE, APA Engineered Wood Specialist.

Learning Objectives:

  1. Participants will investigate past and current methods for determining force transfer around openings for wood shear walls through discussion of the joint research project of APA – The Engineered Wood Association, the University of British Columbia (UBC), and the USDA Forest Products Laboratory (FPL).
  2. Participants will compare the effects of different opening sizes, full-height pier sizes, and their relationships to the three industry shear wall approaches by illustrating use of the segmented, perforated, and FTAO methods.
  3. Participants will observe how the study examined internal forces generated during loading by reviewing full-scale wall test data as well as analytical modeling performed in determining statistical accuracy.
  4. Participants will conclude that research results obtained from this study can be used to support different design methodologies in estimating forces around openings accurately.

Learn more


Best Practices for Force Transfer Around Openings

Wood structural panel sheathed shear walls and diaphragms are the primary lateral-load-resisting elements in wood-frame construction. As wood-frame construction is continuously evolving, designers in many parts of the U.S. are optimizing design solutions that require the understanding of force transfer between elements in the lateral load-resisting system.


Options for Shear Walls With Openings

The U.S. building codes provide three solutions to walls with openings. The first, often referred to as the “segmented shear wall method,” ignores the contribution of the wall segments above and below openings and only considers the full-height segments in resisting lateral forces. The second is the “perforated shear wall method,” which accounts for the effects of openings in the walls using an empirical reduction factor.

The final method is “force transfer around openings” (FTAO). Much engineering consideration has been given to this topic and excellent examples have been developed. But very little test data have been collected to verify various rational analyses. Typically, walls that are designed for force transfer around openings attempt to reinforce the wall such that it performs as if there was no opening. Generally, increased nailing in the vertical and the horizontal directions, as well as blocking and strapping, are common methods used for the reinforcement around openings.

FTAO holds a couple of advantages over segmented shear walls: more versatility, because it allows for narrower wall segments while still meeting the height-to-width ratios and, often, fewer required hold-downs.


FTAO Techniques

There are three techniques that are most commonly used to predict force transfer around openings: drag strut, cantilever beam, and the Diekmann technique. The drag strut technique is a relatively simple rational analysis that treats segments above and below the openings as drag struts. This analogy assumes that the shear loads in the full-height segments are collected and concentrated into the sheathed segments above and below the openings.

The cantilever beam technique treats the forces above and below the openings as moment couples, which are sensitive to the height of the sheathed area above and below the openings.

The Diekmann technique, named for the California structural engineer who developed it, assumes that the wall behaves as a monolith and internal forces are resolved by creating a series of free body diagrams. Although the technique can be tedious for walls with multiple openings, many engineering offices have developed spreadsheets or software based on the method. A known limitation of this technique is that when the height above the opening is small, the resolved shear forces become quite large, resulting in the apparent overstressing of the wood structural panel sheathing.

APA, the USDA Forest Products Laboratory, and the University of British Columbia conducted a joint research project to evaluate the variations of walls with pier widths that meet code-prescribed limitations. Using a series of 12 wall configurations, the study examined the internal forces generated during testing and evaluated the effects of size of openings, location of openings, size of full-height piers, and different construction techniques by using the segmented method, the perforated shear wall method, and the Diekmann method.


Results and Recommendations

The results of the study showed that there is a wide range of predicted forces among the FTAO methods that were considered for this study. The variations result in some structures being either over-built or less conservative than the intended performance objective.

The results of the measured versus predicted strap forces determined that the drag-strut method was consistently unconservative; so while it’s the easiest to implement, it is the least conservative of the three methods. On the opposite end, the cantilever beam method was found to be consistently ultra-conservative, leading to potential for over-detailing of walls to resolve the force transfer around openings. The Diekmann method, and the similar SEAOC (Structural Engineers Association of California) method, provided reasonable agreement with measured strap forces.

In the meantime, APA is working with the research team on a Phase II study that will help further refine APA’s FTAO recommendations. The study will expand the initial research, in accordance with the Diekmann method, to provide the strap forces for a range of openings that may be used for designing walls with openings.

To read the full results of the Phase I testing by each wall segment, download Joint Research Report: Evaluation of Force Transfer Around Openings—An Experimental and Analytical Study, Form M410.